Categories

BATTERY HOLDER

Sort By:
Show:
  • 1xAA Battery Holder
    1xAA Battery Holder Description This is a battery holder with 150mm long wire. You can use AA-sized Alkaline or Rechargeable batteries with it. Batteries are not included.    ..
    S$0.60
  • 2 AA Battery Holder with 9V Snap
    2 AA Battery Holder with 9V Snap Two AA battery holder with snaps to attach 9V battery clip wires. For general purpose electronic kits and projects. Holds two 1.5V AA batteries in series for 3V output With snaps for wire connections Dimensions:  refer to diagram image ..
    S$1.50
  • 2xAA Battery Holder
    2xAA Battery Holder Description This is a battery holder with 150mm long wire. You can use AA-sized Alkaline or Rechargeable batteries with it. Batteries are not included.    ..
    S$0.60
  • 3002  Battery Sizes Accepted:Coin Cell - 20mm
    3002  Battery Sizes Accepted:Coin Cell - 20mm     Product Information     Battery Sizes Accepted: Coin Cell - 20mm Contact Material: Phosphor Bronze Battery Terminals: SMD Mounting Type: SMD For Use With:      20mm coin cell Qty Per Pack : 10   ..
    S$12.00
  • 3xAA Battery Holder
    3xAA Battery Holder Description This is a battery holder with 150mm long wire. You can use AA-sized Alkaline or Rechargeable batteries with it. Batteries are not included.    ..
    S$1.00
  • 6 x AA Battery Holder with Switch and Cover
    6 x AA Battery Holder with Switch and Cover Enclosed battery holder for six AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder’s leads. The leads are about 150mm, and the last 5mm of them are tinned. Screw not included.   ..
    S$3.20
  • 9V Battery Case w/ Switch and Barrel Connector
    Description • 9V battery pack with on/off switch • Use this to power your Arduino • Ready to go out of the box • Battery & screw not included The 9V Battery Case w/ Switch and Barrel Connector is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box. ► Battery and screw not included! Dimensions • Size: 68mm x 33mm x 21mm ( 2.6in x 1.3in x 0.84in ) • Weight: 22.1g • Lead Length: 12cm / 5in ..
    S$2.50
  • 9V Battery Clip  to 2.1 Barrel Jack
    This simple cable has so many uses! Plug a 9V battery into one end and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack. Use this cable to battery-power any device that needs 9V and has an on-board barrel jack - it works great for Arduinos, development boards, evaluation boards, and more!   ..
    S$1.50
  • 9V Battery Clip to Dupont Connector Male - SOLID TAP - 10/PACK
    9V Battery Clip to Dupont Connector Male What is it? Is a 9V Battery Clip with two single male Dupont Connectors.  Why did you make it? To power breadboard projects with battery packs or 9V battery’s without the bad feeling of cheap battery clips with tinned leads. What makes it special? The connection is reliable and robust compared to tinned battery clip leads. Two single male Dupont Connectors provide flexibility. A quality battery clip gives beginners and professionals comfort during bread boarding.     ..
    S$10.00
  • Button Cell Battery Holder (LR44 x 3)
    Introduction This small capsule is a 4.5V button cell battery holder for mini power solutions.Its minimalism design in clean white cylinder body and matte surface makes it an elegant power capsule in your projects. It does not includes 3* LR44 cell battery.   Use this small battery holder to drive our wearable MCU--Cheapduino     Specification Material:Plastic Color:White   Shipping List Button Cell Battery Holder   (1 unit) LR44 cell battery (Not Included)   Documents                          LR44 datasheet       ..
    S$1.80