Categories

Motion Control Modules

Sort By:
Show:
  • 10 Amp DC Motor Driver
    10 Amp DC Motor Driver MD10C is a newer version of the MD10B which is designed to drive high current brushed DC motor up to 10A 13A continuously.  It offers several enhancements over the MD10B such as support for both locked-antiphase and sign-magnitude PWM signal as well as using full solid state components which result in faster response time and eliminate the wear and tear of the mechanical relay.   Read User's Review: http://www.robotshop.com/en/cytron-13a-5-30v-single-dc-motor-controller.html   **Note that it is not for "RC PWM"    *MD10C is now Revision 3.0. * Rev 3.0 can support motor voltage range from 5V to 30V  Features: Bi-directional control for 1 br..
    S$19.00
  • A4988 Reprap Stepper Driver with Heat Sink - Pack of 4
    A4988 Reprap Stepper Driver with Heat Sink - Pack of 4       A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to the easy implementation. As long as the "step" input inputting one pulse drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened. In the micro-step operation, A4988 ch..
    S$15.50
  • A4988 Stepper Motor Driver Carrier with Voltage Regulators
    This is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. It has two voltage regulators (5 V and 3.3 V), eliminating the need for separate logic and motor supplies. The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 – 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling). This board ships with 0.1″ male header pins included but not soldered in.   Description   Specs (10)   Pictures (6)   Resources (3..
    S$14.20
  • DHB-10 Dual H-Bridge 10 Amp Motor Controller
    DHB-10 Dual H-Bridge 10 Amp Motor Controller The DHB-10 is an open-source, 10 amp dual H-bridge motor controller, for the Arlo Robot platform or our Motor Mount and Wheel Kit. It features an onboard multicore Propeller microcontroller to provide precise closed-loop or open-loop control for two individual motor channels. The DHB-10 comes preloaded with open-source firmware designed specifically for use with the Arlo robot platform or Motor Mount & Wheel Kit, and BASIC Stamp Board of Education, BOE Shield with Arduino Uno, or Propeller Activity Board.  Firmware updates may be loaded using a Prop Plug. (The current firmware is not designed for supporting other motor control applications.) Features Built-in 8-core 80 MHz Propeller P8X32A microcontroller wit..
    S$172.00
  • L298N Dual H Bridge Stepper Motor Driver Module
    L298N Dual H Bridge Stepper Motor Driver Module PRODUCT DESCRIPTION L298N Dual H Bridge DC Stepper Motor Drive Controller Board Module For Arduino   The L298 Stepper Controller makes it easy to  drive either two DC motors or a bipolar stepper motor. This is a very high quality board and is very compact for designs where space really matters. Features :   Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logic current 0mA-36mA ..
    S$9.50
  • Pololu Dual VNH5019 Motor Driver Shield for Arduino
    Pololu Dual VNH5019 Motor Driver Shield for Arduino Get your Arduino moving! This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. These great drivers also offer current-sense feedback and accept ultrasonic PWM frequencies for quieter operation. The Arduino pin mappings can all be customized if the defaults are not convenient, and the motor driver control lines are broken out along the left side of the shield for general-purpose use without an Arduino. Overview P..
    S$75.00
  • RepRap Carrier Board for 3D Printer V1.3
    RepRap Carrier Board for 3D Printer V1.3 Product Info Sanguinololu is highly integrated with all the functions that a 3D printer needs. It is of high capacity-price ratio and support Reprap style printer and other CNC devices (Computer numerical control devices).  The 4 stepper drivers are completely compatible with A4988 and DRV8825. Sanguinololu adapts developer friendly expansion port supporting I2C,SPI,UART,as well as ADC pins. All 14 expansion pins are reserved to be GPIO as well. Power supply for sanguinololu is also flexible; users can choose ATX-4 power input or the 2pin connector to supply. CARRIER Features: 1.  support multiple communication configurations : UART1(RX TX)、I2C(SDA SCL)、SPI(MOSI..
    S$98.00
  • RoboClaw 2x15A Motor Controller (V5)
    RoboClaw 2x15A Motor Controller (V5) The RoboClaw motor controllers from Ion Motion Control (formerly Orion Robotics) can control a pair of brushed DC motors using USB serial, TTL serial, RC, or analog inputs. Integrated dual quadrature decoders make it easy to create a closed-loop speed control system. This version can supply a continuous 15 A per channel (30 A peak). Dimensions Size: 2.1″ × 2.9″ × 0.9″ Weight: 60 g General specifications Motor channels: 2 Control interface: USB; non-inverted TTL serial (2-way); RC servo pulses; analog voltage1 Minimum operating voltage: 6 V Maximum opera..
    S$179.90
  • WorldSkills NI myRIO (For Academic Purchase Only - upon approval)
    WorldSkills NI myRIO  NI myRIO, industry-standard reconfigurable I/O (RIO) technology, the enclosed version of myRIO (myRIO-1900) places three I/O connectors, wireless capabilities, a dual-core ARM real-time processor, and a customizable Xilinx FPGA in the hands of students. With its onboard devices, seamless software experience, and library of courseware and tutorials, myRIO provides a controller ideal for the WorldSkills Mobile Robotics Competition. Purchase Only: Includes WIFI and MSP Connector. (Can only be purchased for use with the WorldSkills Mobile Robotics Competition and Academic  - upon NI approval)           ..
    S$980.00